If you use a low-power surge protector, it won’t stop the breakers from tripping That’s right. But only your appliance-compatible high-power surge protector can stop breakers from tripping!
Why does a low-power surge protector not stop breakers from tripping? Basically, breakers are designed to break a circuit in case a problem occurs. Surge protectors are designed to prevent or reduce the damage of power surges and/or low voltage. So it will not stop tripping if it’s not power compatible with your breaker.
To protect against power surges or low voltage for the house, a whole house surge protection device must be installed at the main electrical circuit board. So that it will stop power surges from entering your home.
When breakers trip, it means that the surges are too powerful or large for the device to handle. For this reason, you should use more than one surge protector to protect your appliances. Keep in mind sometimes your breaker fails without tripping but it is rear if you use a high power breaker.
Why Circuit Breaker Trips?
A circuit breaker can trip for several reasons. When a circuit is overloaded with current, the breaker will trip in order to protect the wires and the electrical appliances you’re using.
Below are some matters why a circuit breaker trips.
1. Circuit overload
The most common cause is when there’s too much current running through the wires. If you’re using more appliances than the wiring can handle, the electricity will flow through the wires until it heats up the wire insulation to the point that it melts. The circuit breaker trips when this happens to prevent a fire.
2. Faulty wiring
A circuit breaker can also trip if there is faulty wiring somewhere in your house. For example, if the screw on your electrical outlet is not tightened all the way, it may cause a short. This will allow too much current to flow through your outlet and trip your breaker.
3. Grounding problems
A ground fault interrupter (GFI) is an electrical outlet used to prevent shocks in the event that someone comes in contact with a “live” wire in your home. It’s essentially a circuit breaker built inside of the outlet and will trip if current runs through it when no appliances are turned on.
4. Short circuits
A short circuit happens when there is a direct connection between the “hot” wire and the “neutral” or “ground” wire. For example, if your toaster wire touches one of the metal prongs on your electrical outlet (while it’s still plugged in), this will cause a short circuit. This can be incredibly dangerous as it can lead to fires or electrocutions.
What to Do When Your Circuit Breaker Trips?
First, you should unplug all of the appliances plugged into the outlet when your circuit breaker trips. If one appliance trips the breaker, they all need to be turned off. If an appliance trips your breaker and you can’t find anything, plug it into the outlet again.
Then turn it on. If that doesn’t work, plug the other appliances into different outlets. Whenever that happens again, there may be a problem with that appliance, so you should unplug it immediately. When your circuit breaker trips often, an electrical or one of the above problems may not help you to find out, you should hire a licensed electrician.
FAQs
It’s a good question, so why is TV tripping your circuit breaker? Maybe the circuit can’t provide enough power to the TV. In other words, if you have 42″ television that requires 300 watts of electricity, it will require far more power than a computer, which only needs 15-20 watts. If everything is connected to one outlet strip, there will be a power outage, which will result in your circuit breaker tripping continuously.
Yes, tripping a circuit breaker in hot weather is unpleasant for everyone, so how to stop it? The answer might be in the question. Try adding a new circuit to your house and have a licensed electrician install it. You can also try adding an outlet strip with a circuit breaker to each outlet in your house. In addition, if the tripping only occurs when certain appliances are used, you may need to check their voltage requirements and see if their voltage supply is compatible with your home’s voltage supply.
Last Words
Finally, try to follow the above points to avoid tripping a circuit breaker. Also, using a high-power surge protector is the best way to protect your appliances and electronics from power surges and it will stop tripping breakers.
Besides, don’t use so many devices in a single power strip or surge protector, try to use separate outlet strips with a circuit breaker or fuse box to connect with each device.
